- 您现在的位置：买卖IC网 > Sheet目录337 > LT3599IFE#PBF (Linear Technology)IC LED DRVR WHITE BCKLGT 28TSSOP
LT3599
OPERATION
The LT3599 uses a constant-frequency, peak current mode
control scheme to provide excellent line and load regula-
tion. Operation can be best understood by referring to the
Block Diagram in Figure 1.
To turn on the LT3599, the V IN pin must exceed 3.1V and
the SHDN /UVLO pin must exceed 1.4V. The SHDN /UVLO
pin threshold allows programming of an undervoltage
lockout (UVLO) threshold for the system input supply us-
ing a simple resistor divider. A 4μA current ?ows into the
SHDN /UVLO pin before the part turns on and is removed
after the part turns on. This current hysteresis allows the
programming of hysteresis for the UVLO threshold. See
“Shutdown Pin and Programming Undervoltage Lockout”
in the Applications Information section. For part switching,
the PWM pin must exceed 1V (typical). For micropower
shutdown, the SHDN /UVLO pin at 0V reduces V IN supply
current to approximately ~0μA.
LT3599 has a built-in boost converter which converts the
input voltage to a higher output voltage for driving LEDs.
The LED strings are connected to current sources where
the current level is set with an external resistor on the
I SET pin. The LED1 to LED4 voltages are monitored for
the peak switch current limit and, hence, the inductor
current available to the output LEDs.
Dimming of the LEDs is accomplished by either PWM dim-
ming or analog dimming. PWM dimming is achieved by
pulsing the LED current using the PWM pin. For constant
color LED dimming, the LT3599 provides up to a 3000:1
wide PWM dimming range by allowing the duty cycle of the
PWM pin to be reduced from 100% to as low as 0.033%.
When the PWM pin is low, switching is disabled and the
error ampli?er is turned off so that it does not drive the V C
pin. Also, all internal loads on the V C pin are disabled so
that the state of the V C pin is maintained on the external
compensation capacitor. This feature reduces transient
recovery time. When the PWM input again transitions
high, the peak switch current returns to the correct value.
In applications where the user can sacri?ce OPENLED ,
SHORTLED fault ?ag diagnostics, the dimming ratios can
be as high as 3000:1. Analog dimming of LED currents is
accomplished by varying the level of CTRL pin voltage.
This method, however, changes LED color since dimming
is achieved by changing LED current. For CTRL pin voltage
less than 1V, LED current is de?ned as:
I LED = V CTRL ? ?
outputvoltageregulation.Duringnormaloperation,when
all LEDs are used, the lowest LED pin voltage (LED1 to
LED4) is used to regulate the output voltage to ensure all
? 1330 ?
? R ISET ? ?
( Amps )
LED strings have enough voltage to run the programmed
current.
If the user prefers only three strings, then LED string 4 can
be disabled through the DISABLE4 pin and by connecting
LED4 to any other LED pin. If the user prefers only two
strings, then two pins are connected in parallel (i.e., LED1,2
and LED3,4 can be connected together in operation).
The basic loop uses a pulse from an internal oscillator
to set the SR latch and turn on the internal power NPN
switch Q1. The signal at the noninverting input of the PWM
comparator (A2) is proportional to the sum of the switch
current and oscillator ramp. When this signal exceeds the
V C voltage, the PWM comparator resets the latch. The
switch is then turned off, causing the inductor current
to lift the SW pin and turn on an external Schottky diode
connected to the output. Inductor current ?ows via the
Schottky diode charging the output capacitor. The switch
is turned on again at the next reset cycle of the internal
The LT3599 uses the FB pin to provide overvoltage protec-
tion when all LED strings are open. There is an internal
PMOS switch between V OUT and V O_SW that is controlled
by the PWM signal. During the PWM off-period, this
PMOS is turned off, allowing for higher dimming range
and lower current during shutdown. A resistor divider is
connected between the V O_SW pin and ground, which sets
the overvoltage protection voltage.
If the LED1-4 pin voltage is below 0.3V, the string is treated
as an open LED string. As a result, an OPENLED ?ag is
set. If a LED string is opened during regular operation,
the output voltage will regulate to the optimum voltage
for the remaining connected strings.
If a short occurs between V OUT and any LED pin during
operation, the LT3599 immediately turns off the shorted
channel and sets a SHORTLED ?ag. Disabling the channel
protects the LT3599 from high power thermal dissipation
oscillator. During normal operation, the V C voltage controls
and ensures reliable operation.
3599fe
9
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
LT3743EFE#PBF
IC LED DVR HP CONST CURR 28TSSOP
LT3745IUJ#TRPBF
IC LED DVR 16CH 50MA 40QFN
LT3746IUHH#TRPBF
IC LED DRIVER 32CHANNEL 56-QFN
LT3754IUH#TRPBF
IC LED DVR 16CH 50MA 32QFN
LT3755EMSE#PBF
IC LED DRVR HP CONS CURR 16-MSOP
LT3760EFE#PBF
IC LED DVR WHT/CLR BCKLT 28TSSOP
LT3799IMSE#PBF
IC LED DRIVER TRIAC DIM 16-MSOP
LT3956EUHE#PBF
IC LED DVR BUCK BOOST 36-VQFN
相关代理商/技术参数
LT3599IFE#TRPBF
功能描述:IC LED DRVR WHITE BCKLGT 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND
LT3599IFEPBF
制造商:Linear Technology 功能描述:LED Driver 40-Seg 3.3/5/9/../24V TSSOP28
LT3599IFE-PBF
制造商:LINER 制造商全称:Linear Technology 功能描述:4-Channel 120mA LED Driver with ±1.5% Current Matching
LT3599IFETRPBF
制造商:LINER 制造商全称:Linear Technology 功能描述:4-Channel 120mA LED Driver with ±1.5% Current Matching
LT3599IFE-TRPBF
制造商:LINER 制造商全称:Linear Technology 功能描述:4-Channel 120mA LED Driver with ±1.5% Current Matching
LT3599IUH
制造商:LINER 制造商全称:Linear Technology 功能描述:4-Channel 120mA LED Driver with ±1.5% Current Matching
LT3599IUH#PBF
功能描述:IC LED DRIVR WHITE BCKLGT 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C
LT3599IUH#PBF
制造商:Linear Technology 功能描述:LED DRIVER BOOST PWM 2.06MH 制造商:Linear Technology 功能描述:LED DRIVER, BOOST, PWM, 2.06MHZ, QFN-32